How To Fix If Your Dryer Keeps Tripping Breaker – Seven Easy Methods

Dryers often tend to trip breakers due to multiple reasons. People often complain about why their dryer keeps tripping breaker. Therefore, this article will talk about why your dryer keeps tripping breaker and how to solve this issue.

How To Prevent Your Dryer From Tripping:

Firstly, you need to make sure that you have installed your dryer properly. If you did not install your dryer in the right way, you might want to reinstall it. You can contact dryer vent installation and repair Gainesville, GA. They have the best technicians, and the rates are quite affordable. Moreover, their technicians are experienced and qualified, so the installation of your dryer could never go wrong. 

However, if you don’t want professional help, you can fix this issue yourself by reading the below-mentioned information carefully. We have gathered some common reasons for this issue for you.

• Defective Circuit Breaker:

If you ever notice that your dryer is tripping, then a faulty circuit breaker might be a reasonable explanation for this. Normally, a circuit breaker trips when there is an electric current overload on a circuit. Circuit breaker trips to restrict the flow of the current.

Solution:

If your circuit breaker is more than 15 years old, it is wise to change it immediately. Old circuit breakers can not even handle a normal amount of current. That’s why they keep on tripping frequently. The whole process of replacing the circuit breaker is not difficult. You just need to go to the hardware store to get a new one. However, if you are an amateur, be careful during the process. To be on the safe side, you can also call a professional technician. You can also avail of the services of HVAC Cleaning in Gainesville, GA.

• Inspect Your Thermistor:

A faulty thermistor can cause your dryer to trip. The main purpose of a thermal resistor is to control the amount of heat in the dryer. If the thermal resistor, itself, is defective, then it is not able to control the heat. As a result, the dryer heats up. In addition to this, a heated dryer is more prone to tripping.

Solution:

• Firstly unplug the dryer. 
• After that, check the thermistor with the ohmmeter. An ohmmeter will show the value of the conductivity of the thermistor. 
• Thirdly, get the reading of the conductivity of the thermistor.
• Lastly, if there is no reading, you need to replace the thermistor at once.

Thus, you can fix your faulty thermistor in four easy steps.

• Faulty Heating Element:

The heating element is another integral component of a dryer. If it is faulty, then your dryer may not work properly. 

Solution:

If your heating element is getting heated up in no time, then you may want to perform a test on it. Take out your multimeter and check for the continuity of the heating element. This continuity will be in between the terminals and the case. If you find continuity between the terminals and the case, it is time to replace the heating element. A perfect heating element should not have any continuity.  

Moreover, you need to take special care of the heating element as it can short out very easily. Heating element short outs are very hazardous. In addition to this, they can even short out on housing.

• Defective Motor:

Faulty dryer motors can also cause the dryer to trip. If your motor has been shorted out, you need to repair or replace it.

How To Check If Your Motor Has Been Shorted Out Or Not?

You need to follow the same procedure as mentioned earlier to check the continuity of the motor. Please take out your device and connect it with the motor. If the multimeter scale shows continuity, you need to replace it as soon as possible. 

• Defective Terminal Block:

Loose wires in the terminal block may contribute to the tripping of the dryer. This issue can be as minor as loose wires and as major as wire breaking entirely.

Solution:

It would be best to mend your wires as soon as possible as it might become hazardous in the near future.

• Unsecured Electrical Connections:

Unsecured connections and loose ends are other contributing factors to tripping. Loose connections can transfer an inadequate amount of current to the dryer. As a result, the dryer may start tripping. Loose wires can draw more current from the system. This excessive amount of current can trigger the circuit breaker. As a result, the dryer can trip.

Solution:

Firstly, if you see any loose wires, cut off the power supply. Secondly, tighten those hanging wires and loose connections.

• Dirty Bearings:

Bearings may tend to accumulate lint and trash from the dryer. As a result of this accumulation, bearings can become a victim of wear and tear. Due to this, bearings may not work smoothly and offer more resistance. This increased resistance may draw more electrical energy. Moreover, this current can cause the breaker to trip. 

Solution:

The Solution is very simple. It would be best if you cleaned your bearing more often. Most importantly, do not forget to lubricate them with an appropriate lubricant.

Conclusion:

In conclusion, we can say that dryers are very sensitive to electric current. Moreover, Any factor that can draw unneeded amounts of current can cause these dryers to trip.

Also Read: What Are the Benefits of Online HR Training?